OS7070 v4.43a 20091009

[Wi$e]

viewtopic.php?f=213&t=4589

[Wi$e]

New Version Changes
’09.10.09 V4.43a
1. [N090815007/ALL/ALL] TEMP LICENSE display screens in MMC 860 should be changed
2. [P090815002/ALL/ALL] Headset mode cannot be set or unset during conversation
3. [P090815001/ALL/ALL] ABW key cannot be used during phone call
4. [P090813001] KMMC 406 cannot be used set extension 3999 modem as trunk ring.
5. [P080424014/ALL/ALL] ITP5112L OVERLAP MODE OPERATION
6. [-/ALL/ALL] transferred call's CID from AA didn't display
When incoming call with CID is answered by the AA and then transfer to a station (eg; 203) the display of station 203 will not show [CID name and number]. Display show: "TRANS FM 701" on the second line. This is fixed
7. [-/ALL/ALL] can't use IT tool to assign VT key on button 13 of 14 button set
When using software load 4.41 and IT tool version 1.40, to IT tool 4.9.2 (MMC 722) cannot be used to program an VT key on any digital or ITP phone. It’s fixed. When using KMMC programming the VT key on a key phone is not a problem.
8. [-/OS7070/ALL]OS7070 FAN control look-up table changed.
9. [P090822001/ALL/ALL] Missed Calls display causes date lockup on keyset
10. [P090901004] MMC119 Ringing Display on Line 2 is set to None when i5243 connected
11. [P090728007/ALL/ALL] DND FORWARD FUNCTIONALITY OS7400
12. [P090808001/ALL/ALL ] Network forward 2nd Call across network
13. [P090902001/ALL/ALL] Set Relocate does not work between SLT extension and Virtual SLT extension
14. [P090818016/ALL/ALL] E-LCR & Standard SIP phones
15. [-/ALL/USA,RUSSIA,KOR] Changed new Keyset's License policy
Changed new Keyset's License policy
These new keysets are IP2200, IP3100, IP5220, IP5240, IP5243, WIP5120
In case of USA and Russia, you can use these keysets without license.
16. [-/ALL/ALL] DTMF sending through SIP trunk for dialing
If DTMF type is outband, It's possible to send DTMF through SIP trunk for dialing.
17. [-/ALL/ALL] SIP stack failure on the Plant Office system
Reason : The failure stopped all outgoing SIP messages from the OfficeServ, no responses were sent to REGISTER messages from WIP Phones, or from the IP-UMS. Outgoing SIP trunk calls also failed with the message “No User Response” displayed on the calling phone. The OfficeServ did not send any INVITE messages for the outgoing trunk calls.
The SIP functionality was restored by performing a reset of the system in IT Tool menu item: 6.3.1
This problem occurred twice, and appears to have been caused by changing the Peer CLI table parameter in the 5.2.12 SIP Stack/Ext/Trunk Options screen. The value of the Peer CLI table parameter was changed from 1 to 2. Changing it back to 1 did not fix the problem, only a reset solved the problem.
Modification : Whenever trying to send any SIP message for UMS interop, SIP module checks whether the callleg exists or not. When not found, simply ignores the send request from Call module.
18. [-/ALL/ALL] SIP Registration CALL ID bug
Reason : REGISTER messages for multiple users must have unique Call-ID but OfficeServ has same Call-ID for multiple users.
Modification :
1.If Registration status is UnReg, each regClient detach from regClientMgr, so it can be possible for each regClient to use unique Call-ID and CSeq.
2. If Registration status is Reg, Call-ID and CSeq are stored and managed for each user.
19. [-/ALL/ALL] New IPP(5220,5243) LED Color Control
Modified to send both led state and color information when connecting with New IPP(5220,5243).
20. [-/ALL/ALL] Sometimes, call log doesn't save caller name
The caller name was showed on the incoming call but sometimes it showed " Unknown" in the call log.
Modified to send call log information again after receiving FACILITY msg.
21. [P090826001/ALL/ALL] No light indication for DT key that refer to SIP trunk