OS7200 v4.11

[Wi$e]

Прошивка для АТС Samsung OfficeServ 7200
ВНИМАНИЕ! ДЛЯ РАБОТЫ VOIP ТРЕБУЮТСЯ ЛИЦЕНЗИИ!
Версия 4.11

http://www.officeats.ru/product_info.ph ... ml?fid=418
http://samsungpbx.mylivepage.ru/file/18 ... 2_v411.rar

[Wi$e]

MCP S/W changed items
Wireless IP phone license was deleted by request.
- According to the VoIP License Policy, VoIP Stack License was added in OS7200 MCP V4.10.
But wireless IP phone license was deleted in this version by request.
- WIP PHONE can not assign in MMC841 SIP STACK ALLOW option.
- Maximum 32 wireless IP phones are available without license.

Added Features & Modified items
- Added some features and Changed some default values for IP phone’s voice quality.
 MMC835 “DUAL FILTER EC” option was added.
- This option is only available in MGI16/MGI64 card.
: MGI16/ 64 should be modified, and it will be applied from later than V1.19
- Dual filter echo canceller’s parameter of MGI16/MGI64 card will be downloaded differently according to the trunk’s type.
: If this parameter is changed ‘DISABLE <-> 8TRK/8TRK2/DTRK’, MGI Card will be restarted. If this parameter is changed among 8TRK, 8TRK2, DTRK. MGI Card will not be restarted.
- ‘DISABLE’ Mode is Standard EC Mode.
- ‘8TRK’, ‘8TRK2’, ‘DTRK’ modes are Dual Filter EC Mode and only the parameters of mode are different.
- Default – 8TRK2 MODE
- Range – DISABLE, 8TRK MODE, 8TRK2 MODE, DTRK MODE
 MMC841 “ITP MAX TX LIMIT” option was added
- If this option is set to YES, maximum TX level of IP phone can be limited.
- Default – NO
- Range – YES / NO
 SIDETONE VOL’s default data for ITP was changed to 4 in MMC807.
 MIC TX LEVEL’s default data for ITP was changed to 3 in MMC807.
 Some T-SWITCH GAIN default data were changed in MMC809.
ITP <-> ATRK : 0
ITP <-> DTRK : 0

- QSIG Time synchronization feature was added.
When several systems are connected in network with the using of QSIG in TEPRI or VoIP, time synchronization will work.
 MMC820 “TIME SYNC” option was added.
(Default – OFF / Range – OFF/ON)
 This option does not need in SELF, only can assign from SYS(01) to SYS(99).
 If the user want to use SYS(01) system to time master, TIME SYNC option of SYS(01) have to change ON. And then when other system’s station connected in network make a call to SYS(01), time will be synchronized by SYS(01)’s time.

- C-M&A Feature was added in RUSSIA

[Wi$e]

- Change Notes
1. When the country is set, the cid configuration is fixed.
=> We add the MMC to configure the standard of cid, receive level,
transmission level and the coding rule.
2. Four kind of new cards are developed.
=> We developed the new cards and add the interface routine for new cards.
3. Dial Pulse feature of TRK cards(16TRK and 8TRK2) is required.
=> We add Dial Pulse feature to 16TRK/8TRK2.
4. If user cancel MW when SLT's lamp is on, the lamp is not off.
=> We add the condition to blink control routine.
5. If TEPRIa card is E1/T1 mode, system can't display TEPRI version correctly.
=> We modify routine to process version information over 0x20.
6. CID receiver did not work within 5 sec after hook-on in New Zealand.
=> We add non-PRS feature to condition.