Продажа, установка и сервис IP-АТС Panasonic: KX-NS500, KX-NS1000, KX-NCP, KX-TDE, KX-TDA

Прошивка OfficeServ 7100 v4.75 20140211

Прошивки для АТС Samsung OfficeServ7100.

Модератор: TOPPEHTEP

Правила форума
Возможность загрузки файлов доступна интеграторам и корпоративным клиентам!
По вопросам поддержки и доступа Вы можете обратиться:
- На электронную почту: Samsung@OfficeATS.ru
- По телефону: +7 (499) 653-71-72

Прошивка OfficeServ 7100 v4.75 20140211

Сообщение Wi$e 22 фев 2014, 19:26

Прошивка процессора MP10a для АТС Samsung OfficeServ 7100, версия 4.75 20140211.
New Version Changes
’14.02.11 V4.75
1. [P130703002/ALL/ALL] Transfer to WIP5100 stops ringing.
<Issue>
A station which receives an external call transfers the current call to WIP5100 and disconnects itself. WIP5100 stops ringing after 15 seconds.
<Reason>
About 2 years ago system was modified to make WIP5120 ring external bell when WIP5120 receives a blind transferred external call. This modification should not be applied to WIP5100 because it has only one common bell but it was applied to all WIP phones in that time.
(For you reference, WIP5120 has internal and external bells. It selects one of bells depending on call type.)
<Modified>
It is fixed not to apply previous modification to WIP5100.
2. [P131011003/ALL/ALL] Unanswered wake-up calls ring to the second Admin improperly.
<Issue>
Operator station group has more than two ADMINs and its ring mode is UNCONDITIONAL.
Set to wake-up alarm to GUEST room.
If guest does not answer wake-up alarm, system makes a wake-up recall to ADMINs.
In this case one of ADMINs answers wake-up recall and disconnects a call.
After few second, a reminder call rings to the other ADMINs improperly.
<Modified>
System will not make a wake-up recall to the rest ADMINs if wake-up recall is cleared by one of ADMINs.
3. [-/OS7070/ALL] External Page does not work.
<Issue>
OS7070 External Page does not work because External Page port refers to OS7100 port table.
<Modified>
It is fixed to refer right port table.
4. [-/OS7070/ALL] Loud Bell does not work.
<Issue>
OS7070 Loud Bell does not work because there is a relay control error.
<Modified>
Relay control error is fixed.
5. [-/MP20s,MP10a,MP07,MP03/ALL] System Halt due to frequent BRI interrupt.
<Issue>
When BRI interrupt is happened very frequently because of bad chip, noise or disconnecting cable, system becomes halt state and all digital phones display version information.
<Modified>
When too many BRI interrupts are happened so BRI module can’t handle all interrupt messages, it will throw away some interrupt messages which are over restricted message pool size to prevent system halt.
6. [-/MP20s,MP10a,MP07,MP03/ALL] BRI Layer1 Lock up
<Issue>
When system receives abnormal signal, BRI chip is stuck in unknown state. Since then it can’t process Layer1 Deactivate signal.
<Modified>
Even though chip is in unknown state, BRI module will deactivate Layer1 when it receives L1 Deactivate signal.
7. [-/ALL/ALL] MGI port lockup
<Issue>
When system receives SIP trunk call which is routed to unplugged station, MGI port is stuck in unknown state because system tries to make an external call with LCR code 0.
Issue is happened only when LCR code is set to 0.
<Modified>
It is fixed not to make an external call with LCR code in the above case.
8. [-/ALL/ALL] SMDR IA flag is not printed.
<Issue>
Set SIP phone as unconditional station group member. When SIP phone answers the group call, SMDR IA flag is not printed.
<Modified>
It is fixed to show IA flag when SIP phone answers the unconditional group call.
9. [P130604002/ALL/SEUK] Change default UCD Wrap-up time.
For only SEUK, default UCD wrap-up time is changed from 3 to 0 second.
10. [P130530001/ALL/ALL] SMDR Duration of IA flag is displayed as 0.
<Issue>
When Ring Preference is set to station 2xxx and it answers an external call, SMDR duration of IA flag is displayed as 0.
<Modified>
It is fixed not to initiate duration buffer so that right duration is displayed on SMDR.
11. [P130628006/ALL/ALL] Station name display error in case of Hotel Check-in.
<Issue>
Administrator inputs guest name during check-in but this name is not displayed on Large-IP phone (ex. SMT-i5220). Because system does not send guest name to Large-IP phone.
<Modified>
System will send guest name to Large-IP phone.
12. [-/ALL/ALL] Speech issue of SIP trunk call
<Issue>
System can handle only one codec so when it receives 200 OK that has more than two codecs, it selects one of codecs and sends reINVITE to ISP. But particular ISP re-sends reINVITE that has more than two codecs and system also sends reINVITE again.
This situation continues and SIP signaling between OfficeServ and ISP can’t complete. Because of this user has a speech issue.
<Modified>
‘Use First Codec’ option is added in DM5.2.12 SIP Trunk Configuration and DM 5.2.13.
You can see this option with DM V4.75 or later.
If your ISP or opposite system sends reINVITE that has more than two codecs over and over again and has a speech issue because of this, you should set ‘Use First Codec’ to ON.
In this case system will select the first codec of the received codec list and not send reINVITE to ISP or opposite system.
13. [-/ALL/STA] Tolling feature
For only STA, system provides Tolling feature which was already applied to SEUK.
14. [-/ALL/ALL] SIP trunk call disconnection in particular case.
<Issue>
SIP phone user makes a SIP trunk call and does blind transfer to another SIP phone before external user answers the SIP trunk call. In this case if another SIP phone user answers the call first, current call is disconnected.
<Modified>
In previous version, call is disconnected due to SIP message handling error.
With V4.75 or later you can see normal operation.
15. [-/ALL/ALL] IP-UMS is connected to the system even though its IP address is not set to Phone IP White List.
<Issue>
This issue is happened in below case.
- IP-UMS is connected to under V4.70.
- Upgrade the system to V4.70 or later. After completing upgrade, set DM2.1.6 Halt Status from Halt to Restart. (Before upgrading the system, IP-UMS should keep its connection.)
- Do not input any IP address to DM 5.13.10 Phone IP White List.
- In this case IP-UMS does not lose its connection.
<Modified>
In previous version, when Halt Status is changed from Halt to Restart, system does not check Phone IP White List because it misjudges IP-UMS connection state.
It is fixed to check right IP-UMS connection state.
16. [-/ALL/ALL] SIP phone Hold Pickup issue
<Issue>
SIP phone user can pick up a station call on hold with Hold Pickup feature code. But he/she can’t pick up a trunk call on hold with same feature code.
<Modified>
This feature has not been implemented from the beginning.
It is fixed to be able to pick up a trunk call on hold by SIP phone user with Hold Pickup feature code.
17. [-/ALL/ALL] Add confirm tone for WE VoIP user.
<Issue>
When WE VoIP user sets call forward with feature code, error tone is always heard.
Because of this error tone, user is hard to know current setting succeeds or not.
<Modified>
Add confirm tone to inform WE VoIP user that current feature code setting succeeds.
If setting fails, error tone is heard.
※ Make sure that you should use the latest WE VoIP version(V3.5.0.0 or later) for normal
operation.
18. [-/ALL/ALL] MP10a email gateway distorts low audio message when converted to WAV.
<Issue>
When you record a very low audio message, email gateway WAV file is distorted, so it’s hard to understand. But when you hear a message with a telephone, it has no problem.
<Cause>
Email gateway converts audio message G.726 (32kbps) -> 16-bit signed linear pcm (128kbps) -> 8-bit unsigned linear pcm (64kbps), then quantization noise always happens.
If a message is recorded with very low audio volume, it's hard to hear it because the noise level is similar with the level of voice.
<Modified>
New option "Message format of E-Mail gateway" is available in MClass. You can select 8bit pcm (default) or 16bit pcm. If you select 16bit pcm, the quantization noise does not happen, but the converted WAV size becomes twice.
19. [-/ALL/SEI] 'AM' is wrong in 24 hours form in DM 8.11 Status Screen.
<Issue>
In DM 8.11 Status screen, time is displayed in 24 hours form, but 'AM' is attached.
<Cause>
The time is displayed in 24 hours form for Italy, but 'AM' is not fixed.
<Modified>
‘AM' is removed.
20. [-/ALL/ALL] E.164 deny operation error
<Issue>
You have enabled ‘SIP TRK E.164 support’ and entered ‘070’ in DM 5.2.28 E.164 deny table. Then first ‘0’ is discarded when you make a call with “070XXXXXXX”.
<Cause>
There is a logical error. It has to refer the deny table first, but it removes first ‘0’ before it checks deny table.
<Modified>
It’s fixed to check deny table before it edits the numbers.
21. [-/OS7070, OS7030/ALL] CTI application Lockup
<Issue>
Input max entries in DM 3.2.3 DID Ringing table. CTI application becomes halt state when it gets DID table data from the system.
<Cause>
When CTI application requests DID table data, system sends all entries by dividing 100 entries at a time. But in case of OS7030 and OS7070 whose max entry number is a multiple of 100, system does not send end of sending data message to CTI after completing to send all DID entries. So CTI continues to wait until it receives end of sending data from the system to finish DID query.
<Modified>
There’s a timer control error. It is fixed.
22. [-/MP20s,MP10a,MP07,MP03/ALL] Memory Recovery Reset
<Issue>
In particular customer site, slow operation was happened due to memory leak.
At that time average memory was over approximately 90%.
<Modified>
To prevent slow operation, system will reset when its average memory is over 88%.
It is called memory recovery reset and this feature only works when current circumstance meets the below conditions.
- Only Linux system has Memory Recovery Reset feature.
- ‘System Reset for Memory Recovery’ option is added in DM 2.1.5. (default: DISABLE)
To activate the feature, you should set this option to ENABLE.
- When average memory is over 88%, specified flag is set. System always checks this flag is set or not at every 4 am. If it is set at 4 am, system will reset automatically.
You can check memory recovery reset alarm in DM 6.1.1 after system reset.
23. [-/ALL/ALL] MOBEX Executive Auto Record
<Issue>
One way audio issue is happened in below case.
- An inbound call with SIP trunks is made to the MOBEX executive feature code.
- Dial tone is returned to the user.
- They dial extension 201 and are routed to that extension.
- Station 201 has auto record turned on to mailbox 201 with voice mail port 301.
- When the station 201 answers the call, they have one way audio on the call.
When station 201 is not using auto record feature, the one way audio is not present.
<Modified>
There’s a t-switch control error. It is fixed.
24. [-/ALL/ALL] Barge-In LED error
<Issue>
Barge-In LED is not turned off in below case.
- Set Trunk Monitor in DM 5.14.5 to ON and set Barge-In related options.
- Station A is on conversation with SIP/PRI trunk.
- Station B overrides station A and station A disconnects the call.
- In this case Barge-In LED is not turned off.
<Modified>
It is fixed to turn off Barge-In LED when current station becomes IDLE state.
25. [-/ALL/ALL] H.323 Speech issue
<Issue>
Station A has a conversation with external user B with H.323 trunk. Then station A does blind transfer to another external user C with SIP trunk. In this case external user B and C can’t hear each other’s voice.
<Modified>
System sends a codec that is using in H.323 trunk call to opposite party when making a SIP trunk call.
26. [-/ALL/ALL] System reset during MOBEX call
<Issue>
Make a MOBEX call with SIP peering. When the opposite party presses the HOLD button repeatedly and disconnects the call, system resets.
<Modified>
It is fixed to check that opposite party of MOBEX station is valid. If it is not valid, system will not refer to related buffer to prevent system reset.
27. [P131210001/ALL/ALL] VT TRANSFER REMOTE NODE plays main greeting, not subscriber greeting.
<Issue>
VT Transfer in a centralized setup with 1xxxx stations routes to the main menu.
Software V4.53, 4.65, 4.70 and 4.74a have the same issue.
We are testing with a SVMI-20E Voice mail.
Any other stations not starting with a 1xxx work fine.

Node 001 - 7400 (4.53w, 4.65, 4.70d, 4.74a)
Node 002 - 7400 (4.53w, 4.65, 4.70d, 4.74a)

Node 1 has 1xxx extensions and centralized voicemail.
Node 2 has 2xxx extensions

Call comes in via PRI to Node 2 extension 2117. Extension 2117 performs a VT transfer to remote voicemail group 5149 in Node 1. Voicemail answers the call with main greeting, not subscriber greeting.
<Modified>
This issue is happened due to confliction of Network LCR port and Remote Station port.
It is fixed but we recommend that you should follow below recommendation SPNet setting rule for normal operation.
=> You should set SPNet number with 4 digits and these numbers should start with
minimum 2. (For example, 2001 is OK but 1001 is not recommended.)
28. [-/ALL/ALL] NS KEYS USING FORWARD ALL AND FORWARD BUSY
<Issue>
ALL/BUSY forward does not work when a station of second node makes a SPNet call to a station of first node with NS key. In this case ALL/BUSY forward is set to a station of first node and this station is in busy state.
<Cause>
When user selects NS key, system activates PICKUP feature first.
<Modified>
It is fixed to work ALL/BUSY forward with NS key.
29. [P131220001/ALL/ALL] PUBLIC CALLER CID
<Issue>
Public caller is displayed as Caller ID of mailbox in below case.
- Incoming trunk call is routed to VMAA and VMAA calls station A.
- Station A has a call forward setting to forward incoming call to VM.
- Finally incoming trunk call is routed to VM again because of the above forward setting. And in this case Public caller is displayed as caller id of mailbox.
<Modified>
It is fixed to send caller ID.
30. [-/ALL/ALL] Analog Modem can’t be connected to the system.
<Issue>
If DM IP White List is set, Analog Modem can’t be connected to the system.
<Modified>
It is fixed not to apply DM IP White List rule to Analog Modem.
31. [-/ALL/ALL] MOBEX calling number type error
<Issue>
In below case mobile phone user can’t make a call with incoming call number.
- MMC420 PRI Trunk Data > Calling Number Type : NATIONAL
- MMC401 Trunk On/Off > Repeat CLI : ON
- MMC861 System Options > Trunk to Mobex CLI : Received
- MMC328 Mobile Extension: Set to make a call with ISDN trunk
- MMC714 DID Ringing: Incoming ISDN trunk call is routed to designated Mobex station
- When incoming ISDN trunk whose calling number type is INTERNATIONAL is routed to Mobex station, CID of NATIONAL type is displayed on mobile phone. If user tries to make a call with this number, he/she can’t make an international call.
<Modified>
If Repeat CLI option(MMC401) is set to ON and Trunk to Mobex CLI(MMC861) is set to Received, system will send received calling number type instead of MMC420 calling number type.
32. [Bug Fix/ALL/ALL] DM access failure through modem
<Issue>
If DM 5.13.9 DM IP White List was set, DM access was failed through modem.
<Modified>
If DM 5.13.9 DM IP White List was se, It’s possible to access to DM though modem.
33. [Change/Linux system/ALL] Changed saving location of DM user profile.
<Modified>
Utable file for DM user profile is no longer used. DM user profile is only saved in internal memory for security.
34. [P130731001/MP40/ALL] DB backup to SD card
<Issue>
If LP40 auto upgrade feature (MP40’s dip switch5) was set and LP40 version and SP40 file’s LP40 version in MP40 were same. You were not able to access KMMC 815, 818, 819 because of seeing ‘Media is busy’ on LCD.
<Modified>
You can access KMMC 815, 818, 819 in this case.
35. [Bug Fix/Linux system/ALL] Malfunction of Management IP White List feature.
<Issue>
If you enter IP address on DM 5.13.11 Management IP White List and delete all IP address on it. After that, you can access DM from any IP address.
<Modified>
There was an internal file control error. This problem is fixed.
36. [P131017002/ALL/ALL] SIPT > SIPT MGI Use option no longer works.
<Issue>
After transferring a call with SIP trunk to other SIP Trunk, Officeserv used MSP channel instead of MGI channel in spite of setting ‘SIPT > SIPT MGI Use option’.
<Modified>
There was a media (MGI or MPS) selection error. This problem is fixed.
37. [Bug Fix/Linux system/ALL] system halt came from memory leakage when using DNS Server.
<Issue>
system halt came from memory leakage when using DNS Server.
<Changed>
DNS query policy is changed below to prevent system halt.
a. How to query DNS server is changed.
- Officeserv changed how to query DNS server
- Cycle of DNS query during failure of query is changed.
.until 1 hour from start of query: every 20 seconds
.after 1 hour: 1 minute, 2 minutes, 4 minutes …. 128 minutes (max time)
b. DM 2.1.5 ‘Multi DNS Server’ option is added for user using multi ISP. (Default : Disable)
If ‘Multi DNS Server’ option is disabled, Officeserv use only DM 5.6.1 DNS Server 1/2 options.
If ‘Multi DNS Server’ option is enabled, Officeserv use DM 5.6.1 DNS Server 1/2 options and DM 5.2.13 DNS Server 1/2 options at the same time.
c. DM 2.1.5 ‘System Reset for Memory Recovery’ option is added (default : Enable)
If Average memory usage is over 88% because of memory leakage, OfficeServ is automatically rebooted at 4 AM.
d. If DND query is failed, This information is saved in DM 6.1.1 Alarm History by using expression ‘Memory Rec(means Recovery) Reset’
e. If you change DM 5.6.1 ‘DNS IP address’, OfficeServ is rebooted automatically.
38. [-/ALL/ALL] IP-UMS’s fax receiving failure from SIP ISP which don’t support T.38
<Issue>
If you use IP-UMS, you should set Fax option to T.38 because IP-UMS only supports T.38
In this case, if SIP ISP doesn’t support T.38 there was a fax receiving problem.
<Modified>
If you receive Fax call from SIP ISP, You can select each ISP to send reINVITE with T.38 or not respectively.
In this problem case, you can set DM 5.2.13 ‘T.38 Reinvite’ option to ‘Not Send’ for not sending reINVITE with T.38 and working with Fax pass through mode.


5
0
Голосов нет
4
0
Голосов нет
3
0
Голосов нет
2
0
Голосов нет
1
0
Голосов нет
 
Всего голосов : 0

Если нужна помощь, услуги по настройке\обслуживанию или поставке оборудования, обращайтесь:
Телефон: +7 (499) 653-71-72 внутр. 101
С уважением, Денис.
Офисные АТС.ру
Аватара пользователя
Wi$e
Администратор
 
Торренты: 511
Комментарии: 63
Раздал: 198.26 Гб
Скачал: 2.29 Гб
Ратио: 86.531
Сообщения: 4564
Зарегистрирован: 18 июн 2006, 15:00
Откуда: Москва
Квалификация: Инженер ТЦ производителя
Организация: Офис-Девайс
Для Спасибо: Яндекс.Деньги:4100198401725

Вернуться в Officeserv7100 ROMS

Кто сейчас на конференции

Сейчас этот форум просматривают: нет зарегистрированных пользователей и гости: 0


Продажа, установка и сервис IP-АТС NEC: SL1000, SV9100, SV9300, SV8100, SV8300, SV9500, SV8500



Пириногвые IP-АТС Symway. Консультация, Поставка, Внедрение.
cron