Неправильный CID

[eso46]

Content840 подключённый по E1 не отображает CID. Для проверки к OS7400 подключил по E1 Asterisk. При этом стал наблюдать в логах asterisk что OS7400 добавляет перед номером символ «*» . Т.е. номер 4401 передается как *4401 (у меня нумерация на 4-ку). По SIP у меня работает все корректно. Где я мог ошибиться?

[LionB]

Для проверки, на самой карте TEPRIа можно снять ISDN трэйс.
Процедура в аттаче.
После трэйса не забудь выключить трэйс msgt off

[eso46]

Спасибо, попробую.
OS7400 нормально отдает номер на Asterisk только при QSIG Trunk установленном в Normal, в остальных случаях перед номером идёт *.
К сожалению Content840 у меня не работает с Normal. На Content плата настроена: SOFVL1M -межстанциооная master, L2ML3S - уровень 2 master, уровень 3 slave.

[eso46]

OS7400 V4.70
TEPRIa V4.48

Вызов номера 4126.
Телефоны 4100- 4399 на Content, 4401-4499 на Samsung.
Номер 4401 виден как *4401.

Трэйс:

TEPRI>motf +M
ISDN Msg Monitor ON

IPC .......... OFF
ALARM ........ OFF
MONITOR ...... ON
D-CHANNEL .... OFF
FULL AUDIT ... OFF
STATE ........ OFF
ABCD ......... OFF
TRAFFIC ...... OFF

TEPRI>msgt on
Message Trace Set ON !!

debug_ap_flag 00 40 4B A0
debug_l3_flag 00 40 4B A1
debug_l2_flag 00 40 4B A2
debug_l1_flag 00 40 4B A3

TEPRI>
___________________________________________________________________________

00:02:04 Port 00 NT->NET
+Raw data
00 01 01 01

+Layer2
SAPI=00 C/R=00 TEI=00 N(R)=00 P/F=01 RR-Frame

___________________________________________________________________________

00:02:04 Port 00 NT<-NET
+Raw data
00 01 01 01

+Layer2
SAPI=00 C/R=00 TEI=00 N(R)=00 P/F=01 RR-Frame

___________________________________________________________________________

00:02:34 Port 00 NT->NET
+Raw data
00 01 01 01

+Layer2
SAPI=00 C/R=00 TEI=00 N(R)=00 P/F=01 RR-Frame

___________________________________________________________________________

00:02:34 Port 00 NT<-NET
+Raw data
00 01 01 01

+Layer2
SAPI=00 C/R=00 TEI=00 N(R)=00 P/F=01 RR-Frame

___________________________________________________________________________

00:03:04 Port 00 NT->NET
+Raw data
00 01 01 01

+Layer2
SAPI=00 C/R=00 TEI=00 N(R)=00 P/F=01 RR-Frame

___________________________________________________________________________

00:03:04 Port 00 NT<-NET
+Raw data
00 01 01 01

+Layer2
SAPI=00 C/R=00 TEI=00 N(R)=00 P/F=01 RR-Frame

___________________________________________________________________________

00:03:07 Port 00 NT->NET
+Raw data
00 01 00 00 08 02 01 00 05 04 03 80 90 A3 18 03
A1 83 81 1C 30 9F AA 0E 80 01 00 A1 02 80 00 82
01 01 A3 02 80 00 92 01 00 A1 1A 02 01 FF 06 04
2B 0C 09 00 30 0F 80 0B 20 20 20 20 20 20 20 20
20 20 20 05 00 6C 06 80 2A 34 34 30 31 70 05 80
34 31 32 36 7D 02 91 81 A1

+Layer2
SAPI=00 C/R=00 TEI=00 N(S)=00 N(R)=00 P/F=00 I-Frame

+Layer3 : SETUP
Q.931 user-network call control message
Call reference value 01 00
IE BEARER CAPABILITY(04) length 03
1------- Octet 03 Not Extended
-00----- Coding standard CCITT
---00000 Info Transfer capability Speech
-00----- Transfer mode Circuit
---10000 Info transfer rate 64 kbit/s
IE CHANNEL IDENTIFICATION(18) length 03
1------- Octet 03 Not Extended
-0------ Interface implicitly identified
--1----- Other Interface ex. PRI
----0--- Indicated channel is preferred
-----0-- Indicated channel is not D-channel
------01 As indicated
-00----- Coding standard CCITT
---0---- Channle is indicated by number
----0011 B channel units
-0000001 Channel number OR Slot map 01
IE FACILITY(1C) length 48
1------- Octet 03 Not Extended
-00----- Coding standard CCITT
---111-- HLC interpretation unknown
------11 Unknown HLC protocol profile
-0101010 Outband negotiation not possible
-0001110 Outband negotiation not possible
IE CALLING PARTY NUMBER(6C) length 06
1------- Octet 03 Not Extended
-000---- Unknown Type of number
----0000 Unknown Numbering Plan
Calling Party Number *4401
IE CALLED PARTY NUMBER(70) length 05
1------- Octet 03 Not Extended
-000---- Unknown Type of number
----0000 Unknown Numbering Plan
Called Party Number 4126
IE HIGH LAYER COMPATIBILITY(7D) length 02
1------- Octet 03 Not Extended
-00----- Coding standard CCITT
---100-- First HLC ID to be used
------01 Higher layer protocol profile
-0000001 HLC id Telephony
IE SENDING COMPLETE(A1)
___________________________________________________________________________

00:03:07 Port 00 NT<-NET
+Raw data
00 01 01 02

+Layer2
SAPI=00 C/R=00 TEI=00 N(R)=01 P/F=00 RR-Frame

___________________________________________________________________________

00:03:08 Port 00 NT<-NET
+Raw data
7E 80 00 00 00 70 06 1B 65 07 01 FF 00 70 00 01
00 30 00 00 00 40 41 00 01 01 00 01 00 00 00 00
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00 00 00 00 00 00 00 00 00 FF 00 00 FF FF 04 00
00 30 00 01 00 11 00 2A 00 FF FF 00 00 FF FF 00
FF 00 01 02 00 12 01 04 00 00 00 0C 01 07 BF 15
FF FF 50 4F 01 01 05 00 45 50 2A 4F 42 00

+Layer2
SAPI=31 C/R=01 Wrong Address feild in Layer 2 octet_val 2

___________________________________________________________________________

00:03:08 Port 00 NT->NET
+Raw data
02 01 01 02

+Layer2
SAPI=00 C/R=01 TEI=00 N(R)=01 P/F=00 RR-Frame

___________________________________________________________________________

00:03:12 Port 00 NT<-NET
+Raw data
7E 80 00 00 00 7C 06 1B 62 07 01 FF 00 7C 00 01
00 30 00 00 00 4C 56 00 01 01 00 01 00 00 00 00
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00 00 00 00 00 00 00 00 00 FF 04 00 00 30 00 01
00 11 00 2A 00 FF FF 00 00 FF FF 00 FF 00 01 02
00 12 01 06 00 00 00 0C 01 07 BF 96 FF FF 51 2A
01 01 05 00 45 50 2A 4F 42 31

+Layer2
SAPI=31 C/R=01 Wrong Address feild in Layer 2 octet_val 2

TRAP code = 0011 @ ../../tepri2/D_isdn/services/com_proc.c 1244